When using Aluminum Electrolytic Capacitors, please observe the following points to ensure optimum capacitor performance and long life.

1>DC electrolytic capacitors are polarized.

Make sure of the polarity which is marked on the body of the capacitor.  
Application of the reversed voltage may cause a short circuit or damage to the capacitor.  
Use bipolar capacitors when the polarity is not determined or unknown.  
Note that DC electrolytic capacitors CAN NOT be used for AC application.

2>Bipolar capacitors
These capacitors are used only in pulse circuits as well as polarity reverse circuits, but not applicable in pure AC or high ripple current. 

3>Do not apply voltage greater than the rated voltage
If a voltage exceeding the rated voltage is applied, the leakage current will increase, which will damage the capacitor.  
Recommended working voltage is 70% - 80% of rated voltage.  
Using capacitors at recommended working voltage prolongs capacitor life.

4>Do not allow excessive ripple current through the capacitor
The flow of ripple current greater than the permissible (rated) value will cause heating of the capacitor, which may decrease the capacitance and damage the capacitor.
Ripple current through the capacitor must be at or below the allowable level, generally not more than 80% of the rated current.

5>Use specially designed capacitors for the circuits where charge and discharge are frequently repeated.
In circuits subjected to rapid charge and discharge cycles, a capacitor may be damaged and its life may be shortened by capacitance decrease at higher temperature.  

6. Operating temperature range.

The characteristics of capacitors change with the operating temperature.  
The capacitance and leakage current increase and dissipation factor will decrease at higher temperatures. Usage at lower temperature will ensure longer life.

7. Temperature vs. Life.

The expected life of a capacitor is related to its ambient temperature. 
Generally, if the ambient temperature is reduced 10℃, life is doubled at rated voltage. 

8. Check operating frequency.

Electrolytes usually have their capacitance measured at 100 Hz. or 120 Hz.  
However, remember that capacitance decreases and dissipation factor increase as the applied frequency becomes higher.

9. Capacitor Storage

Long periods of storage have virtually no effect on a capacitor’s capacitance and dissipation factor. 
However, such periods can increase leakage current and decrease the capacitors withstand voltage. 
Apply rated DC voltage treatment to the capacitors which have been stored for a long time.

10. The capacitor case is not insulated from the cathode terminal.

The capacitor’s case and cathode terminal connect through the electrolyte. 
If the case is to be completely insulated, that insulation must be at the capacitor’s mounting point.

11. Do not apply excessive force to the terminals and leads.

An excessively strong force applied to the terminals and lead wires may cause leads to break or terminals to separate and, in turn, cause the internal contact to fail.

12. Cleaning of the circuit board after solder dipping.

Clean circuit boards to remove flux or other extraneous matter.  
To ensure protection for the sleeve, its marking, and the capacitor's sealing materials, the capacitor should never be washed or cleaned by halogenous agents or solvents such as trichlorethylene, xylene, acetone, etc. 
Recommended cleaning solvents; Methanol, isopropanol ethanol, isobutene, petroleum ether, propanol and/ or commercial detergents.

13. Be cautious of the temperature and duration when soldering.
Soldering irons should be kept away from vinyl-insulated sleeves of capacitor.  
When the capacitor is dipped in a solder bath, use at less than 260℃ and 10 seconds to avoid damaging the capacitor.

14. Hole positions on the circuit board.
When designing a circuit board, space the through-holes equal to the space between the capacitor's lead wires. 
If the spacing is either greater than or less than the capacitor's leads, mounting will apply stress to the leads, causing short circuits, broken circuits, and increased current.
Also, through-holes on the circuit board as well as lead holes of post-process parts can result in solder splashing onto the vinyl sleeve causing damage.  
Consider hole positions carefully.

Dear Customer,

Kingtronics SMD Aluminum Electrolytic Capacitor has good quality package to protect, so you can rest assured the transport process. Besides, you can place an order according to the following form, the minimum order quantity for each size is different, and it should be ordered full container load.

Reel size: Diameter 38cm
Large box size (Long * wide * high): 42*42*56cm
Small box size (Long * wide * high) : 40*40*13cm

Product Size, mm
Smallest packaging
Plate, piece
Small box, piece
Large box, piece
4X5.4/5.8
2000
10000
40000
5X5.4/5.8
1000
5000
20000
6.3X5.4/5.8
1000
5000
20000
6.3X7.7
1000
5000
20000
8X10.5
500
2000
8000
10X10.5
500
2000
8000
12.5X13.5
250
1000
3000

Hurry to contact with us, you can possess Kingtronics excellent after-sales service! http://www.kingtronics.com/

My distinguished guests:

I am willing to introduce the advantages of Kingtronics SMD Aluminum E cap for you. Compared with other capacitors, SMD Aluminum Electrolytic Capacitor’ s advantages can be listed as follows:

1. The capacitance per unit volume of aluminum capacitors is particularly large, the lower operating voltage, this feature is more outstanding. Therefore, the aluminum capacitors is particularly suitable for miniaturization and large capacity of the capacitor. It is noteworthy that its small size, light weight, volume and weight only about 1/10 of the traditional components.

2. Kingtronics SMD Aluminum Electrolytic Capacitor has best in class high-frequency performance, it can reduce the interference of electromagnetic and radio frequency.

3. Kingtronics SMD Aluminum Electrolytic Capacitor is easy to achieve automation and improve production efficiency. It not only reduces 30% to 50% of the cost, but also saves material, energy, equipment, manpower, time and so on.

4. The defects of the SMD Aluminum Electrolytic Capacitor can be repaired at any time during the working process and restore its insulation capacity. Besides, the dielectric oxide film of the Aluminum Electrolytic is able to withstand very high electric field strength, this is more than 30 times the paper capacitor.

The advantages of Kingtronics SMD Aluminum Electrolytic Capacitor are far more than what I said, if you want to know more about SMD E cap, we would like to inform you with pleasure! Please refer to Kingtronics website: http://www.kingtronics.com/aluminum-electrolytic-capacitors/

Do you know about the application of Kingtronics SMD Aluminum Electrolytic Capacitor? I would like to tell you something about it.

With the advancement of modern technology and the continuous improvement of capacitor performance, owing to its small size, big storage power and highly cost effective, V-Chip Aluminum Electrolytic Capacitor is widely used in consumer electronics, communications products and peripheral products, new energy, automotive industry and so on.

Typical applications of V-Chip Aluminum Electrolytic Capacitor:
1. It applied to in-vehicle electric equipment, and also can support the anti-vibration type.
2. It is used in high-definition television, including digital set-top boxes, LCD, car DVD.
3. DC-link capacitors in AC/DC converters for variable-frequency drive and frequency changers as well as in uninterruptible power supplies.
4. Energy storage for airbags, photoflash devices, civil detonators.

Kingtronics produces and sells many kinds of SMD Aluminum Electrolytic Capacitors professionally with long life, no matter what you need, you can always find products that make you satisfied here. More information about SMD E cap please visit Kingtronics official website:
http://www.kingtronics.com/aluminum-electrolytic-capacitors/

We are willing to recommend our high quality products to you! Kingtronics has very competitive price of Kingtronics GKT-VK SMD E Cap. its quality is guaranteed and trustworthy. We have built a long-term business relationship with lots of customers around the world. You can rely on Kingtronics!

Features of GKT-VK SMD E-Cap
KZ code printed on the GKT-VK Aluminum Electrolytic Capacitors Surface
Designed for surface mounting on high density circuit board
Extra Lower Impedance
Reach/RoHS certified quality
Long load life: 3000 hours
Wide range capacitance: 4.7uF ~ 4700Uf
Various dimensions: 4*5.4mm ~ 16*16.5mm

Specifications of GKT-VK SMD E-Cap
Operating Temperature: -55℃~ +105℃
Voltage Range: 6.3V~ 50V.DC
Capacitance Tolerance: ±20 % at 120Hz, 20℃

Kingtronics welcomes your SMD E cap inquiry and order, hurry to contact with us now! http://www.kingtronics.com/aluminum-electrolytic-capacitors/GKT-VK-105C-SMD-Aluminum-Electrolytic-Capacitors.html

Contact us

Tel: (86) 769 8118 8110
Tel: (852) 8106 7033
Fax: (852) 8106 7099
E-mail: info@kingtronics.com
Skype: kingtronics.sales
MSN: kingtronics-sales@hotmail.com
Web: www.Kingtronics.com
YouTube: www.youtube.com/c/Kingtronicskt

About

Kingtronics International Company was established in 1995 located in Dongguan City of China to handle all sales & marketing for factories located in Chengdu, Sichuan and Zhaoqing, Guangdong, China. In 1990, we established the first factory to produce trimming potentiometer and in 1999 we built up new factory in Zhao Qing, Guangdong. Now with around 850 workers, Kingtronics produce trimming potentiometers, dipped tantalum capacitors, multilayer ceramic capacitors, and diode & bridge rectifier. We sell good quality under our brand Kingtronics, and Kt, King, Kingtronics are our three trademarks. All our products are RoHS compliant, and our bridge rectifier have UL approval. Please visit our Products page, you could please download all our PDF datasheet and find cross reference for our Trimming Potentiometer and capacitors.

Tantalum and Ceramic Capacitors Cross Reference ↓ Download
Diodes & Rectifiers List(PDF: 97KB) ↓ Download
Trimming Potentiometer Cross Reference ↓Download

Archives

Calendar

<< 2024-3 >>

Sun

Mon

Tue

Wed

Thu

Fri

Sat

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31