Kingtronics produce and sell a wide variety of Aluminum Electrolytic Capacitors with long life, low Impedance and excellent performance options. 

Welcome your inquiry for more information. 

Catalogue: 
http://www.kingtronics.com/pdf/Kingtronics-Aluminum-Electrolytic-Capacitors-Catalog.pdf

Product Video: 
https://www.youtube.com/watch?v=dOTQpigQKgc

*Load Life: 1000Hr ~10000Hr
*Operating temperatures: 85°C, 105°C, 130°C
*Capacitance: 3.3uF - 22000uF
*Voltage range: 6.3 ~ 160 WV
*ISO/RoHS certified quality
Axial Type, Radial Type, SMD Chip Type, Snap-in Type, Screw Type and Lug Type
*Package: Ammo, Bulk, Tape & Reel 

When using Aluminum Electrolytic Capacitors, please observe the following points to ensure optimum capacitor performance and long life.

1>DC electrolytic capacitors are polarized.

Make sure of the polarity which is marked on the body of the capacitor.  
Application of the reversed voltage may cause a short circuit or damage to the capacitor.  
Use bipolar capacitors when the polarity is not determined or unknown.  
Note that DC electrolytic capacitors CAN NOT be used for AC application.

2>Bipolar capacitors
These capacitors are used only in pulse circuits as well as polarity reverse circuits, but not applicable in pure AC or high ripple current. 

3>Do not apply voltage greater than the rated voltage
If a voltage exceeding the rated voltage is applied, the leakage current will increase, which will damage the capacitor.  
Recommended working voltage is 70% - 80% of rated voltage.  
Using capacitors at recommended working voltage prolongs capacitor life.

4>Do not allow excessive ripple current through the capacitor
The flow of ripple current greater than the permissible (rated) value will cause heating of the capacitor, which may decrease the capacitance and damage the capacitor.
Ripple current through the capacitor must be at or below the allowable level, generally not more than 80% of the rated current.

5>Use specially designed capacitors for the circuits where charge and discharge are frequently repeated.
In circuits subjected to rapid charge and discharge cycles, a capacitor may be damaged and its life may be shortened by capacitance decrease at higher temperature.  

6. Operating temperature range.

The characteristics of capacitors change with the operating temperature.  
The capacitance and leakage current increase and dissipation factor will decrease at higher temperatures. Usage at lower temperature will ensure longer life.

7. Temperature vs. Life.

The expected life of a capacitor is related to its ambient temperature. 
Generally, if the ambient temperature is reduced 10℃, life is doubled at rated voltage. 

8. Check operating frequency.

Electrolytes usually have their capacitance measured at 100 Hz. or 120 Hz.  
However, remember that capacitance decreases and dissipation factor increase as the applied frequency becomes higher.

9. Capacitor Storage

Long periods of storage have virtually no effect on a capacitor’s capacitance and dissipation factor. 
However, such periods can increase leakage current and decrease the capacitors withstand voltage. 
Apply rated DC voltage treatment to the capacitors which have been stored for a long time.

10. The capacitor case is not insulated from the cathode terminal.

The capacitor’s case and cathode terminal connect through the electrolyte. 
If the case is to be completely insulated, that insulation must be at the capacitor’s mounting point.

11. Do not apply excessive force to the terminals and leads.

An excessively strong force applied to the terminals and lead wires may cause leads to break or terminals to separate and, in turn, cause the internal contact to fail.

12. Cleaning of the circuit board after solder dipping.

Clean circuit boards to remove flux or other extraneous matter.  
To ensure protection for the sleeve, its marking, and the capacitor's sealing materials, the capacitor should never be washed or cleaned by halogenous agents or solvents such as trichlorethylene, xylene, acetone, etc. 
Recommended cleaning solvents; Methanol, isopropanol ethanol, isobutene, petroleum ether, propanol and/ or commercial detergents.

13. Be cautious of the temperature and duration when soldering.
Soldering irons should be kept away from vinyl-insulated sleeves of capacitor.  
When the capacitor is dipped in a solder bath, use at less than 260℃ and 10 seconds to avoid damaging the capacitor.

14. Hole positions on the circuit board.
When designing a circuit board, space the through-holes equal to the space between the capacitor's lead wires. 
If the spacing is either greater than or less than the capacitor's leads, mounting will apply stress to the leads, causing short circuits, broken circuits, and increased current.
Also, through-holes on the circuit board as well as lead holes of post-process parts can result in solder splashing onto the vinyl sleeve causing damage.  
Consider hole positions carefully.

Kt Kingtronics Snap-in type Aluminum Electrolytic Capacitors is composed of some parts. It can be used in switch mode power supplies (SMPS), drives, welding equipment, uninterruptible power supplies (UPS), and other power electronic applications.
GKT-SS is our main product of snap-in type Aluminum Electrolytic Capacitors for 85°C, 2000H operation, which is the cost-effective choice.

Specifications:
Capacitance Tolerance( 25°C,120Hz): ±20%  
Operating Temperature Range: -40°C~+85°C(450V:-25°C~+85°C)
Rated Range:10V,16-35V,50-100V,160-200V,250-400V,450V
Capacitance Range: 68 - 27,000 µF

Check more information of Kt Kingtronics Aluminum Electrolytic Capacitors, please see: http://www.kingtronics.com/aluminum-electrolytic-capacitors/ 
or consult with our sales team info@kingtronics.com.

Kt Kingtronics best Aluminum Electrolytic Capacitors include Radial Type, Snap-in Type and SMD chip Type. Now we would like to commend Snap-in Type to you, very good quality and very competitive price. Snap-In Aluminum Electrolytic Capacitors are standard 85⁰C or 105⁰C capacitors that can withstand 2000-5000 hours with high ripple current. 
Applications include automotive power, industrial LED lighting, telecom infrastructure and so on.

GKT-SS and GKT-ST are available for your choice.

Kingtronics

Life Hours

Temperatures

Characteristic

GKT-SS

2000H

85°C

High Ripple Current

GKT-ST

2000H

105°C

High Ripple Current

Features:
Smaller size
High stability and high Ripple Current 
PCB Mounting 
High frequency, low resistance
Good self-healing performance

Welcome to send us inquiry and know more about our Aluminum Electrolytic Capacitors! We firmly believe our quality, service and support are the keys to keep long business relationship with you.

Good day friends, Kingtronics offer good quality and price for Aluminum Electrolytic Capacitors.
Kindly please check our offers below and share with us your feedback.
For more part numbers and price, please don’t be hesitated to send your inquiry to us! O(∩_∩)O

GKT-Aluminum Electrolytic Capacitor: http://www.kingtronics.com/aluminum-electrolytic-capacitors/

Radial Type: GKT-GS, GKT-GT, GKT-GH, GKT-GL
GKT-GS 10uF 50V +/-20%  dimension: 5*11mm Bulk RoHS   US$0.0059/pc QTY: 100kpcs
GKT-GH 68uF 25V +/-20% dimension: 5*12mm Bulk RoHS   US$0.0075/pc QTY: 100kpcs

Snap-in Type: GKT-SS, GKT-ST
GKT-SS 3300uF 50V +/-20%  dimension: 22*35mm Bulk RoHS   US$0.51/pc QTY: 100kpcs

SMD Type: GKT-VA, GKT-VT
GKT-VA 100uF 16V +/-20%  Ø4 x 5.4~5.8 mm Tape & Reel RoHS   US$0.0133/pc QTY: 100kpcs

Kt Kingtronics Snap-in type Aluminum Electrolytic Capacitors is composed of some parts. It includes switch mode power supplies (SMPS), drives, welding equipment, uninterruptible power supplies (UPS), and other power electronic applications.

Performance Characteristics of Kingtronics GKT-SS Snap-in E Cap. 

Features

Load life of 2000 hours at 850c

Smaller size

High ripple current

PCB Mounting

Capacitance Range

68  27,000 µF

Rated Voltage

10  450 VDC

Operating Temperature

-40 to +85°C

Capacitance Tolerance

±20% at 100 Hz / +20°C

The reliability of a component can make it performs satisfactorily under a given set of conditions. 
More details please refer to our date sheet link:
http://www.kingtronics.com/pdf/GKT-SS-85C-Snap-in-Aluminum-Electrolytic-Capacitors.pdf

Capacitor parameters for the series equivalent-circuit model is shown on the below table. Among them, C represents Capacitance; DF is short for Dissipation Factor; Rs is the abbreviation of Equivalent Series Resistance; Z symbols Impedance; Ls is Inductance and fo stands for Self-Resonant Frequency and etc. Please find more fully information in it. 

Parameter

Unit

Symbol

Capacitance

farads (F)

C

Capacitive Reactance

ohms (Ω)

Xc

Current

amperes (A)

I

Dissipation Factor

none

DF

Energy

oules (J)

E

Equivalent Series Resistance

ohms (Ω)

Rs

Frequency

hertz (Hz)

f

Impedance

ohms (Ω)

Z

Inductance

henries (H)

Ls

Inductive Reactance

ohms (Ω)

XL

Loss Angle

degrees (°)

δ

Phase Angle

degrees (°)

Θ

Power

watts (W)

P

Power Factor

none

PF

Quality Factor

none

Q

Self-Resonant Frequency

hertz (Hz)

fo

Voltage

volts (V)

V

Volt-Amperes

V-A

VA

Kingtronics produce and sell a wide variety of Aluminum Electrolytic Capacitors with long life, low Impedance and excellent performance options.
If you have interested in these products and need more information, welcome to contact us. Thank you!

Past 10 years we Kingtronics only sell Aluminum e-cap in Mainland & HK, at the beginning of 2016 we turn to overseas market, many customer feedback our prices is very wonderful.

Welcome check prices with us !

Kingtronics (Kt) Aluminum Electrolytic Capacitor Product List

Aluminum Electrolytic Capacitors - Radial Type

Kingtronics P/N

Life Hours

Temperatures

Characteristic

Datasheet

GKT-GS

2000H

85°C

Super Miniaturized

Download PDF

GKT-GT

2000H

105°C

High Temperature

Download PDF

GKT-GH

2000H

105°C

Low Impedance

Download PDF

GKT-GL

5000H

105°C

Long Life

Download PDF

Aluminum Electrolytic Capacitors - Snap-in Type

Kingtronics P/N

Life Hours

Temperatures

Characteristic

Datasheet

GKT-SS

2000H

85°C

High ripple current

Download PDF

GKT-ST

2000H

105°C

High ripple current

Download PDF

Aluminum Electrolytic Capacitors - SMD Type

Kingtronics P/N

Life Hours

Temperatures

Characteristic

Datasheet

GKT-VA

2000H

85°C

4V ~ 100V.DC

Download PDF

GKT-VT

1000H

105°C

4V ~ 100V.DC

Download PDF

 

Kt Kingtronics produces and sells a wide variety of Aluminum Electrolytic Capacitors with long life, low Impedance and excellent performance options. We’d like to share below information about Kt Kingtronics GKT-SS with you.

Specifications:
Capacitance Tolerance (25,120Hz): ±20%
Operating Temperature Range: -40
~+85℃ (450V:-25~+85)
Rated Range:10V, 16-35V,50-100V,160-200V,250-400V,450V

Features:
Load Life of 2000 hours at 85
, Smaller Size;
High frequency, low resistance, good self-healing performance; 
Nominal capacitance in μF;
High stability and high Ripple Current;
PCB Mounting, Standard, general Product ,Long Life;
Safety vent construction passive electronic component.

Application:
Mainly applied to audio, LED LIGHTING DRIVER, energy-saving lamps, electronic ballasts, inverter, power supply and computer industrial and telecommunication fields. They are used for switching power supply, general inverters, UPS, etc. that require small-size capacitors with relatively large-capacitance. Well engineered with great details to ensure high stability and reliability. 

For more details, please click:
http://www.kingtronics.com/pdf/GKT-SS-85C-Snap-in-Aluminum-Electrolytic-Capacitors.pdf

Aluminum Electrolytic Capacitor, simply called Eelectrolytic Capacitor (e-cap), is a type of capacitor that uses electrolyte to achieve larger capacitance than other capacitor types. It consists of cathode aluminum foil, electrolytic paper, electrolyte, and aluminum oxide film, which acts as the dielectric, formed on the anode foil surface.

Due to its large capacitance, Aluminum Electrolytic Capacitor is suitable for passing or bypassing low frequency signals and storing large amounts of energy. It widely be used in power supplies and for decoupling unwanted AC components from DC power connections.

Kingtronics produce Aluminum Electrolytic Capacitor for many years. We sold this product in China and Hong Kong before. Because of good price and quality, we have much success in this item. Now we start offering this product to our oversea customers.

Kingtronics Aluminum Electrolytic Capacitors features in breif:

● long life, low Impedance and excellent performance options|
● Type: radial type, snap-in type
● Rated Voltage (V): 6.3V, 10V, 16V, 25V, 35V, 50V, 63V, 80V, 100V, 160V, 200V, 220V, 250V, 350V, 400V, 420V, 450V
● Operating temperatures up to 150°C

Datasheet:
Aluminum Electrolytic Capacitors - Radial Type
GKT-GS   http://www.kingtronics.com/pdf/GKT-GS-85C-Radial-Aluminum-Electrolytic-Capacitors.pdf
GKT-GT   http://www.kingtronics.com/pdf/GKT-GT-105C-Radial-Aluminum-Electrolytic-Capacitors.pdf 
GKT-GH  http://www.kingtronics.com/pdf/GKT-GH-105C-Radial-Aluminum-Electrolytic-Capacitors.pdf
GKT-GL   http://www.kingtronics.com/pdf/GKT-GL-105C-Radial-Aluminum-Electrolytic-Capacitors.pdf

Aluminum Electrolytic Capacitors - Snap-in Type
GKT-SS   http://www.kingtronics.com/pdf/GKT-SS.pdf
GKT-ST   http://www.kingtronics.com/pdf/GKT-ST.pdf

For more information, welcome contact and send your inquiry to us. : )
info@kingtronics.com

Contact us

Tel: (86) 769 8118 8110
Tel: (852) 8106 7033
Fax: (852) 8106 7099
E-mail: info@kingtronics.com
Skype: kingtronics.sales
MSN: kingtronics-sales@hotmail.com
Web: www.Kingtronics.com

About

Kingtronics International Company was established in 1995 located in Dongguan City of China to handle all sales & marketing for factories located in Chengdu, Sichuan and Zhaoqing, Guangdong, China. In 1990, we established the first factory to produce trimming potentiometer and in 1999 we built up new factory in Zhao Qing, Guangdong. Now with around 850 workers, Kingtronics produce trimming potentiometers, dipped tantalum capacitors, multilayer ceramic capacitors, and diode & bridge rectifier. We sell good quality under our brand Kingtronics, and Kt, King, Kingtronics are our three trademarks. All our products are RoHS compliant, and our bridge rectifier have UL approval. Please visit our Products page, you could please download all our PDF datasheet and find cross reference for our Trimming Potentiometer and capacitors.

Tantalum and Ceramic Capacitors Cross Reference ↓ Download
Diodes & Rectifiers List(PDF: 97KB) ↓ Download
Trimming Potentiometer Cross Reference ↓Download

Meet Kingtronics in Moscow soon
Chip EXPO 2017
Chip EXPO 2017
"Expocentre" Moscow Russia
Date: Oct 31 - Nov 2nd, 2017
Booth No.: B 20

Meet Kingtronics in Munich soon
Electronica 2018
Electronica 2018
New Munich Trade Fair Centre, Germany
Date: 13-16 November, 2018
Booth No.: To be advised

Calendar

<< 2018-5 >>

Sun

Mon

Tue

Wed

Thu

Fri

Sat

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31