When using Aluminum Electrolytic Capacitors, please observe the following points to ensure optimum capacitor performance and long life.

1>DC electrolytic capacitors are polarized.

Make sure of the polarity which is marked on the body of the capacitor.  
Application of the reversed voltage may cause a short circuit or damage to the capacitor.  
Use bipolar capacitors when the polarity is not determined or unknown.  
Note that DC electrolytic capacitors CAN NOT be used for AC application.

2>Bipolar capacitors
These capacitors are used only in pulse circuits as well as polarity reverse circuits, but not applicable in pure AC or high ripple current. 

3>Do not apply voltage greater than the rated voltage
If a voltage exceeding the rated voltage is applied, the leakage current will increase, which will damage the capacitor.  
Recommended working voltage is 70% - 80% of rated voltage.  
Using capacitors at recommended working voltage prolongs capacitor life.

4>Do not allow excessive ripple current through the capacitor
The flow of ripple current greater than the permissible (rated) value will cause heating of the capacitor, which may decrease the capacitance and damage the capacitor.
Ripple current through the capacitor must be at or below the allowable level, generally not more than 80% of the rated current.

5>Use specially designed capacitors for the circuits where charge and discharge are frequently repeated.
In circuits subjected to rapid charge and discharge cycles, a capacitor may be damaged and its life may be shortened by capacitance decrease at higher temperature.  

6. Operating temperature range.

The characteristics of capacitors change with the operating temperature.  
The capacitance and leakage current increase and dissipation factor will decrease at higher temperatures. Usage at lower temperature will ensure longer life.

7. Temperature vs. Life.

The expected life of a capacitor is related to its ambient temperature. 
Generally, if the ambient temperature is reduced 10℃, life is doubled at rated voltage. 

8. Check operating frequency.

Electrolytes usually have their capacitance measured at 100 Hz. or 120 Hz.  
However, remember that capacitance decreases and dissipation factor increase as the applied frequency becomes higher.

9. Capacitor Storage

Long periods of storage have virtually no effect on a capacitor’s capacitance and dissipation factor. 
However, such periods can increase leakage current and decrease the capacitors withstand voltage. 
Apply rated DC voltage treatment to the capacitors which have been stored for a long time.

10. The capacitor case is not insulated from the cathode terminal.

The capacitor’s case and cathode terminal connect through the electrolyte. 
If the case is to be completely insulated, that insulation must be at the capacitor’s mounting point.

11. Do not apply excessive force to the terminals and leads.

An excessively strong force applied to the terminals and lead wires may cause leads to break or terminals to separate and, in turn, cause the internal contact to fail.

12. Cleaning of the circuit board after solder dipping.

Clean circuit boards to remove flux or other extraneous matter.  
To ensure protection for the sleeve, its marking, and the capacitor's sealing materials, the capacitor should never be washed or cleaned by halogenous agents or solvents such as trichlorethylene, xylene, acetone, etc. 
Recommended cleaning solvents; Methanol, isopropanol ethanol, isobutene, petroleum ether, propanol and/ or commercial detergents.

13. Be cautious of the temperature and duration when soldering.
Soldering irons should be kept away from vinyl-insulated sleeves of capacitor.  
When the capacitor is dipped in a solder bath, use at less than 260℃ and 10 seconds to avoid damaging the capacitor.

14. Hole positions on the circuit board.
When designing a circuit board, space the through-holes equal to the space between the capacitor's lead wires. 
If the spacing is either greater than or less than the capacitor's leads, mounting will apply stress to the leads, causing short circuits, broken circuits, and increased current.
Also, through-holes on the circuit board as well as lead holes of post-process parts can result in solder splashing onto the vinyl sleeve causing damage.  
Consider hole positions carefully.

Kingtronics began to sell Aluminum Electrolytic Capacitor to overseas market in year 2016, before that, we sold to Chinese mainland and Hong Kong over 10 years with good reputation.

Recently the result proves our strategy is correct, now more and more oversea customers give us positive good feedback for price and quality, and place order to us. Some of our distributor voluntarily help promote our brand E-cap on exhibition, we believe we also can bring profit to your company and support you in your market. 

The E-cap is widely be used in the application of LED, Lighting Tech, power supply, Custom, Adapters, Front End, POE, Open Frame, Capacitor Chargers, DC to DC, Compact PCI, Micro TCA, Military……

We expand E-cap production line for more specification to meet our customer’s difference requirement. Below our SMD E-CAP product series and specification, welcome feel free to check our product datasheet and send your inquiry to us, let us do best to support you.

Aluminum Electrolytic Capacitor product website: 
http://www.kingtronics.com/aluminum-electrolytic-capacitors/

Kingtronics P/N

Type

Load Life

Temperatures

Voltage Range

Package

Characteristic

GKT-VA

SMD Type

2000H

85°C

4V ~ 100V

Tape & Reel

Standard

GKT-VT

SMD Type

1000H~2000H

105°C

4V ~ 100V

Tape & Reel

Standard

GKT-VC

SMD Type

2000H

85°C

6.3V ~ 50V

Tape & Reel

Low Leakage Current

GKT-VE

SMD Type

2000H-3000H

105°C

6.3V ~ 50V

Tape & Reel

Long Life

GKT-VK

SMD Type

2000H-3000H

105°C

6.3V ~ 50V

Tape & Reel

Extra Lower Impedance

GKT-VL

SMD Type

3000H-5000H

105°C

6.3V ~ 100V

Tape & Reel

Extra Long Life

GKT-VN

SMD Type

1000H

85°C

6.3V ~ 50V

Tape & Reel

Bi-polar

GKT-VZ

SMD Type

1000H-2000H

105°C

6.3V ~ 50V

Tape & Reel

Low Impedance

GKT-VU

SMD Type

3000H

105°C

160V ~ 450V

Tape & Reel

Long Life

GKT-VD

SMD Type

6000H

105°C

160V ~ 450V

Tape & Reel

Long Life

GKT-VW

SMD Type

10000H

105°C

6.3V ~ 450V

Tape & Reel

Long Life

Dear valued customers, the year 2017 is becoming to the end, how is everything going? : )
Kingtronics team hopes you have a harvest and business increasing year.

Kingtronics production line will be very tight before every Christmas, in order to help maintaining the same offer and put order into production flow in time successfully, 
Kindly please feel free to advise us your new request and shipment instruction in advance, then we can prepare and proceed the case.

Kingtronics team sincerely wishs you and your family have a wonderful Merry Christmas and Happy new 2018 year in advance.

Kingtronics strong production lines:

RKT--Trimming potentiometer

RKT-3006P           25pcs/tube
RKT-3386F            50pcs/tube
RKT-3296X           50pcs/tube
RKT-3266W         50pcs/tube
RKT-C3305           2.5kpcs/Reel

MKT--Radial multilayer ceramic capacitor

0.1uF 50V +/-10% X7R  P:5.08MM (0805)  Ammo RoHS         2.5kpcs/Ammo
2200pF 50V +/-2% NPO P: 5.08mm              Bulk RoHS   

GKT-Aluminum Electrolytic Capacitor

Radial Type         
GKT-GS  2200uF 63V +/-20%  dimension: 18*35mm P:7.5mm 85°C Bulk RoHS        
GKT-GT   2200uF 50V +/-20%  dimension: 16*35mm P:7.5mm 105°C Bulk RoHS    

SMD Type 
GKT-VA  33uF 63V +/-20%    size: 8*10.5mm  85°C  Tape & Reel  RoHS            
GKT-VT   470uF 35V +/-20%    size: 12.5*13.5mm 105°C  Tape & Reel RoHS 

My distinguished guests:

I am willing to introduce the advantages of Kingtronics SMD Aluminum E cap for you. Compared with other capacitors, SMD Aluminum Electrolytic Capacitor’ s advantages can be listed as follows:

1. The capacitance per unit volume of aluminum capacitors is particularly large, the lower operating voltage, this feature is more outstanding. Therefore, the aluminum capacitors is particularly suitable for miniaturization and large capacity of the capacitor. It is noteworthy that its small size, light weight, volume and weight only about 1/10 of the traditional components.

2. Kingtronics SMD Aluminum Electrolytic Capacitor has best in class high-frequency performance, it can reduce the interference of electromagnetic and radio frequency.

3. Kingtronics SMD Aluminum Electrolytic Capacitor is easy to achieve automation and improve production efficiency. It not only reduces 30% to 50% of the cost, but also saves material, energy, equipment, manpower, time and so on.

4. The defects of the SMD Aluminum Electrolytic Capacitor can be repaired at any time during the working process and restore its insulation capacity. Besides, the dielectric oxide film of the Aluminum Electrolytic is able to withstand very high electric field strength, this is more than 30 times the paper capacitor.

The advantages of Kingtronics SMD Aluminum Electrolytic Capacitor are far more than what I said, if you want to know more about SMD E cap, we would like to inform you with pleasure! Please refer to Kingtronics website: http://www.kingtronics.com/aluminum-electrolytic-capacitors/

Do you know about the application of Kingtronics SMD Aluminum Electrolytic Capacitor? I would like to tell you something about it.

With the advancement of modern technology and the continuous improvement of capacitor performance, owing to its small size, big storage power and highly cost effective, V-Chip Aluminum Electrolytic Capacitor is widely used in consumer electronics, communications products and peripheral products, new energy, automotive industry and so on.

Typical applications of V-Chip Aluminum Electrolytic Capacitor:
1. It applied to in-vehicle electric equipment, and also can support the anti-vibration type.
2. It is used in high-definition television, including digital set-top boxes, LCD, car DVD.
3. DC-link capacitors in AC/DC converters for variable-frequency drive and frequency changers as well as in uninterruptible power supplies.
4. Energy storage for airbags, photoflash devices, civil detonators.

Kingtronics produces and sells many kinds of SMD Aluminum Electrolytic Capacitors professionally with long life, no matter what you need, you can always find products that make you satisfied here. More information about SMD E cap please visit Kingtronics official website:
http://www.kingtronics.com/aluminum-electrolytic-capacitors/

Do you need our GKT-VN SMD Aluminum Electrolytic Capacitors? All of our products are RoHS compliant and Reach standard. Kingtronics is always your best choice, we also warmly welcome old and new clients to come for business discussions. GKT-VN SMD Aluminum Electrolytic Capacitors is Bi-polar type.

Features of GKT-VN SMD E Cap
CN code printed on the Aluminum Electrolytic Capacitors Surface
Designed for surface mounting on high density circuit board
Reach/RoHS certified quality
Various dimensions: 4*5.4mm ~ 6.3*7.7mm
Bi-polar with general temperature +85℃

Specifications of GKT-VN SMD E Cap
Operating Temperature: -40℃ ~ +85℃
Wide Range Capacitance: 0.1uF ~ 100uF
Voltage Range: 6.3V ~ 50V.DC
Long load life: 1000 hours

Please click the below connection to check more Kingtronics SMD E cap information of it: http://www.kingtronics.com/aluminum-electrolytic-capacitors/GKT-VN-85C-SMD-Aluminum-Electrolytic-Capacitors.html

Kingtronics produce and sell a wide variety of Aluminum Electrolytic Capacitors with Standard, long life, low impedance, Low Leakage Current, Bi-polar and excellent performance options. Load Life from 1000 hours to 5000 hours, and 85°C and 105°C are available.

Now our company release six strong types of SMD Aluminum Electrolytic Capacitors, applications include automotive power, industrial LED lighting, telecom infrastructure and so on.

More details please refer to our official website:http://www.kingtronics.com/

Aluminum Electrolytic Capacitors are incresingly popular recently.
In order to show our valued customers more information, more and more series will be updated on our website.

Except for GKT-VA & GKT-VT, the SMD series GKT-VC,GKT-VE,GKT-VK,GKT-VL,GKT-VN,GKT-VZ have been posted.
Kindly check more specification by below datasheet links !

Welcome to email us to check more part numbers and prices !

GKT-Aluminum Electrolytic Capacitor http://www.kingtronics.com/aluminum-electrolytic-capacitors/

Aluminum Electrolytic Capacitors - SMD Type

Kingtronics P/N

Load Life

Temperatures

Characteristic

Datasheet

GKT-VA

2000H

85°C

Standard

Download PDF

GKT-VT

1000H~2000H

105°C

Standard

Download PDF

GKT-VC

2000H

85°C

Low Leakage Current

Download PDF

GKT-VE

2000-3000H

105°C

Long Life

Download PDF

GKT-VK

2000-3000H

105°C

Extra Lower Impedance

Download PDF

GKT-VL

3000-5000H

105°C

Extra Long Life

Download PDF

GKT-VN

1000H

85°C

Bi-polar

Download PDF

GKT-VZ

1000H-2000H

105°C

Low Impedance

Download PDF


Kt Kingtronics offers high quality product of GKT-VA SMD Aluminum Electrolytic Capacitors, with competitive prices and reliable customer service. We are waiting for your more opportunity and inquiry.

Features:
Designed for surface mounting on high density circuit board;
Emboss carrier tape packing system is available for automatic insertion;
Comply with the RoHS directive.

Specifications:
Operating Temperature: -40°C~+85°C
Voltage Range: 4-100V.DC
Capacitance Rang: 0.1μF ~10000μF
Capacitance Tolerance: ±20% at 120Hz, 20°C

Dimensions (Unit: mm):                                
4*5.4; 5*5.4; 6.3*5.4; 6.3*7.7; 8*6.2; 8*10.5; 10*10.5; 10*13.5; 12.5*13.5; 12.5*16; 16*16.5; 16*21.5

If you have more interested about the details, please reference:
http://www.kingtronics.com/pdf/GKT-VA-85C-SMD-Aluminum-Electrolytic-Capacitors.pdf

Do you interested in purchasing Kingtronics Surface Mount SMD E Cap? Now we will have an introduction of Kt SMD E Cap, hope it will be helpful to you.

We are available to provide more types of SMD E Cap, which includes at least seven types. They are General Purpose Type, Low Leakage Current Type, Non-polarized Type, Low Impedance Type, Long Life Type, High Reliability Type and High Voltage Type.
Among them, General Purpose 's two series Kingtronics GKT-VA and Kingtronics GKT-VT are Kingtronics main selling products. They are also the most popular hot products.

Welcome to try our product Kt Kingtronics Surface Mount SMD E Cap. Looking forward to your enquiries. We will provide best price and utmost service to you.

Contact us

Tel: (86) 769 8118 8110
Tel: (852) 8106 7033
Fax: (852) 8106 7099
E-mail: info@kingtronics.com
Skype: kingtronics.sales
MSN: kingtronics-sales@hotmail.com
Web: www.Kingtronics.com

About

Kingtronics International Company was established in 1995 located in Dongguan City of China to handle all sales & marketing for factories located in Chengdu, Sichuan and Zhaoqing, Guangdong, China. In 1990, we established the first factory to produce trimming potentiometer and in 1999 we built up new factory in Zhao Qing, Guangdong. Now with around 850 workers, Kingtronics produce trimming potentiometers, dipped tantalum capacitors, multilayer ceramic capacitors, and diode & bridge rectifier. We sell good quality under our brand Kingtronics, and Kt, King, Kingtronics are our three trademarks. All our products are RoHS compliant, and our bridge rectifier have UL approval. Please visit our Products page, you could please download all our PDF datasheet and find cross reference for our Trimming Potentiometer and capacitors.

Tantalum and Ceramic Capacitors Cross Reference ↓ Download
Diodes & Rectifiers List(PDF: 97KB) ↓ Download
Trimming Potentiometer Cross Reference ↓Download

Meet Kingtronics in Moscow soon
Chip EXPO 2017
Chip EXPO 2017
"Expocentre" Moscow Russia
Date: Oct 31 - Nov 2nd, 2017
Booth No.: B 20

Meet Kingtronics in Munich soon
Electronica 2018
Electronica 2018
New Munich Trade Fair Centre, Germany
Date: 13-16 November, 2018
Booth No.: To be advised

Calendar

<< 2018-6 >>

Sun

Mon

Tue

Wed

Thu

Fri

Sat

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30