Before using our Kingtronics Radial Aluminum Electrolytic Capacitors, please carefully browse the catalog or product specifications. Then use them within the performance limits’ prescribed. It should not be used where electrical insulation is required.
Connecting with the wrong polarity will short-circuit or damage the capacitor with the pressure relief vent opening early on.

Do not apply a high temperature that exceeds the upper limit of the category range specified for the capacitors. Do not use capacitors in circuits intended for rapid charge and discharge cycle operations.

These products are not intended for use in the following special conditions.
(1) In liquid, such as Water,Oil,Chemicals or Organic solvent.
(2) In direct sunlight, outdoors, or in dust.
(3) In an environment where strong static electricity or electromagnetic waves exist.
(4) Mounting or placing heat-generating components or inflammables, such as vinyl-coated wires, near these products.
(5) Using in the atmosphere which strays Acid or alkaline.
(6) Using in the atmosphere which there are excessive vibration and shock.

For more products information please check:
http://www.kingtronics.com/pdf/GKT-ST-105C-Snap-in-Aluminum-Electrolytic-Capacitors.pdf

•Good shock measures to ensure the Quartz Crystal don’t fall to the ground during use.

• When storing crystals, anti-extrusion measures should be prepared and stored in a dry and ventilated place, avoid damp Quartz Crystal.

• When the solder, solder temperature is not too high, the role of the solder time not too long, so as not to produce an unstable change occurs within the Quartz Crystal.

• Ensure two-pin solder points are not connected, or will lead to Oscillator is stopped.

• The shear pin, should pay attention to the effects of mechanical stress.

• Solder, it should be cleaned to prevent the insulation resistance don’t meet the requirements.

Contact us

Tel: (86) 769 8118 8110
Tel: (852) 8106 7033
Fax: (852) 8106 7099
E-mail: info@kingtronics.com
Skype: kingtronics.sales
MSN: kingtronics-sales@hotmail.com
Web: www.Kingtronics.com

About

Kingtronics International Company was established in 1995 located in Dongguan City of China to handle all sales & marketing for factories located in Chengdu, Sichuan and Zhaoqing, Guangdong, China. In 1990, we established the first factory to produce trimming potentiometer and in 1999 we built up new factory in Zhao Qing, Guangdong. Now with around 850 workers, Kingtronics produce trimming potentiometers, dipped tantalum capacitors, multilayer ceramic capacitors, and diode & bridge rectifier. We sell good quality under our brand Kingtronics, and Kt, King, Kingtronics are our three trademarks. All our products are RoHS compliant, and our bridge rectifier have UL approval. Please visit our Products page, you could please download all our PDF datasheet and find cross reference for our Trimming Potentiometer and capacitors.

Tantalum and Ceramic Capacitors Cross Reference ↓ Download
Diodes & Rectifiers List(PDF: 97KB) ↓ Download
Trimming Potentiometer Cross Reference ↓Download

Meet Kingtronics in Moscow soon
Chip EXPO 2017
Chip EXPO 2017
"Expocentre" Moscow Russia
Date: Oct 31 - Nov 2nd, 2017
Booth No.: B 20

Meet Kingtronics in Munich soon
Electronica 2018
Electronica 2018
New Munich Trade Fair Centre, Germany
Date: 13-16 November, 2018
Booth No.: To be advised

Calendar

<< 2017-10 >>

Sun

Mon

Tue

Wed

Thu

Fri

Sat

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31