Kingtronics Blog

Zener diodes are widely used as voltage references and as shunt regulators to regulate the voltage across small circuits.

When connected in parallel with a variable voltage source so that it is reverse biased, a Zener diode conducts when the voltage reaches the diode's reverse breakdown voltage.

From that point on, the relatively low impedance of the diode keeps the voltage across the diode at that value.

Zener diodes are also used in surge protectors to limit transient voltage spikes.

We have much better prices offer for below zener diode, especially BZX55C and BZV55C.

Do you have inquiry for these zener diode?

Kingtronics Zener Diode Offer:

• 1/2W BZX55C 5V6 DO-35 Bulk or Ammo RoHS
• 1/2W BZV55C 2V7 - BZV55 C47 LL-34 Tape & Reel RoHS
• 1/2W BZX55C 2V7 - 8V2 DO-35 Bulk or Ammo RoHS
• 1W 1N4729A - 1N4756A DO-41 Bulk or Ammo RoHS
• 1/2W ZMM2V4 - ZMM47 LL-34 Tape & Reel RoHS
• 1W ZM4729A - ZM4756A LL-34Tape & Reel RoHS

- Trimming Potentiometer 3296 3006 3386 3323 3329 3362 3266 3309 3590 3540 065 C3305 (SMD 3mm)...
- Diode rectifier: S1M, RS1M, SM4007 melf, BZV55C, UF4007, 1N4007S, 1N4007, 1N5399, RL207, 1N5408, 6A10, FR107, 1N4937, FR157, FR207, 1N5822....etc..
- Bridge rectifier: DB107, DB107S, MB10S, KBL410, KBU610, KBPC2510, KBPC3510, KBPC3510W......etc
- Radial ceramic capacitor cross AVX SR series, Murata RPE, Nippon THD series, Vishay K (Mono Cap ), Kemet C315-C350, Panasonics ECU-S ....
- Radial tantalum capacitor cross AVX TAP series, Kemet T350-T359, NIC NDTM, Nemco TB, Panasonic ECSF...

If you have inquiry, pls send to selina@kingtronics.cn , we will be glad to quote for you! Thank you!

Finding a Bridge Rectifier? How to find the best Bridge Rectifier? Do nothing before you visit our site! We kingtronics is Specialty in design,manufacture of bridge rectifier! We are your best choice.

The bridge rectifier is the most commonly used full wave rectifier circuit for several reasons, one advantage of a bridge rectifier over a conventional full-wave rectifier is that with a given transformer the bridge rectifier produces a voltage output that is nearly twice that of the conventional full-wave circuit.

(1) It does not require the use of center-tapped transformer, and therefore can be coupled directly to the ac power line, if desired.
(2)Using a transformer with the same secondary voltage produces a peak output voltage that is nearly double the voltage of the full wave center-tapped rectifier. This results in the higher dc voltage from the supply.

Kingtronics have UL certification for bridge rectifier, pls see picture of our products, we are glad to get your inquiries!

Hi, dear, do you want to know what size bridge you need to use when replacing? Here I want to share with you my experience.

I get variations of this question quite often, such as: I don't see the bridge used in the Atari AC power "brick"....

My Tempest manual says I need a MDA3501 bridge & I can't find one....What's a suitable replacement for my T3501... and so on.

Like diodes & many other components, the key is usually in the part number. I have added more info on the Parts Page beside each one listed to better aid you.

But I will put a brief note here, as well. In both the examples cited above the bridge is ...from the part number.... a 35[amp]01[ 100 volt].

Generally speaking the first digit/s will refer to the amperage that the bridge is capable of handling & the ending digit/s the voltage it is capable of handling.

As Scotie would say...if you put a 2501 in place of the cited bridge, she's gonna blow!... since the bridge is only able to handle up to 25 amps of current even though the 100 volts is sufficient.

You could go to an "02" 200 volt, "04" 400 volt or higher & still end up with a blown bridge. You need to at least meet both amperage & voltage of the original when replacing.

A good replacement for the cited bridge would be a 3502... disregarding mrf's prefix or suffix.... for 35 amps & capable of handling 200 volts before popping a leg.

Much like sister components.... diodes, capacitors & resistors, you can safely go beyond specs, but not below.

1N4001 [1A50v] can be replaced by any in the series up to 1N4007 [1A1000V]
100uF 160V cap can be replaced by a 100uF 200V or better cap
220 ohm 1/4w resistor can be replaced by a 220 ohm 1/2w resistor

We Kingtronics are a professional bridge rectifier manufacturer. And we have got ISO9001:2008 Certification and UL certification.

If you have inquiry for our bridge rectifier, pls send email to info@kingtronics.com thanks!