The Characteristic of FKT-MD Miniature Size Metallized Polyester Film Capacitor:

1.The small size can be compared favourably with the stacked film capacitor
2.Excellent self-healing property and reliability
3.Low dissipation factor
4.Epoxy resin powder coating provides the identical outer appearance

Specifications:
Rated Voltage:     DC 50/63V, 100V, 250V, 400V, 630V
Capacitance Range:    0.001 TO 3.3uF
Capacitance Tolerance:       ±5%
Dissipation Factor:       ≤1.0%  (20℃,1KHz)

Insulation Resistance:
    C≤0.33Mfd ≥3750MΩ(20℃, 1min)
C>0.33Mfd ≥1250S(20℃, 1min)
FKT-MD: https://www.kingtronics.com/pdf/FKT-MD.pdf

The Characteristic of FKT-MG High Voltage Metallized Polypropylene Film Capacitor:
1.Ideal for high AC current applications, such as CRT deflection for R-F generators and pulse-forming networks.
2.Temperature Coefficient is negative and variety linear over the operation temperature.
3.Coated with flame retardative epoxy resin which provides from humidity and mechanical damage

Specifications:
Operating Temperature:       -40℃ TO + 85℃
Rated Voltage:     DC 1000V, 1250V, 1500, 1600V and 2000V
Capacitance Range:    0.001 TO 0.15Mfd
Capacitance Tolerance:       ±5%, ±10%
Dissipation Factor:       ≤0.1% (20℃, 1KHz)
Insulation Resistance: ≥25000MΩ (CR≤0.1µF) (20℃, 1min)
≥2000s    (CR>0.1µF) (20℃, 1min)
FKT-MG: https://www.kingtronics.com/pdf/FKT-MG.pdf

The Characteristic of FKT-ME Metallized Polypropylene Film Capacitor:
1.Highly reliable because of its excellent Self-Healing performance.
2.Dissipation Factor is normally low and it is stable against high frequency and change of temperature.
3.Recommended for high-frequency circuits like s-curve compensating circuit

Specifications:
Operating Temperature: -40℃ TO + 85℃
Rated Voltage:DC 100V, 250V, 400V, 630V
Capacitance Range:0.01 TO 8.2Mfd
Capacitance Tolerance:±5%, ±10%, ±20%
Dissipation Factor:≤0.001 at1KHz (Typical 0.002 Max)
FKT-ME: https://www.kingtronics.com/pdf/FKT-ME.pdf

The Characteristic of FKT-MP Polyester (Mylar) Film Capacitor-Pei:
1.Good reputation in use with consumer & industrial electronics.
2.Optimum for automatic insertion due to their small size and light weight.
3.Coated with epoxy resin for superior heat resistance, humidity resistance and solvent resistance.

Specifications:
Operating Temperature:-40℃ TO + 85℃
Rated Voltage:DC 100V,250V,400V,630V,1000V,1200V
Capacitance Range:0.001 TO 0.22µF
Capacitance Tolerance:±5%, ±10%, ±20%
Insulation Resistance:0.1µF ≤30,000 MΩ min, >0.1µF >15000 MΩ
Dissipation Factor:≤0.1 (AT 1KHZ)
Dielectric Strength:200% of rated voltage for 5sec.
FKT-MP :https://www.kingtronics.com/pdf/FKT-MP.pdf

As we expand the production capacity of Aluminum El-Cap to meet our customers’ demand, we now have better price support for the Snap-in type E-cap, with fast L/T around 4~6 weeks!
Below is the product series, welcome your inquiry!

kingtronics Snap in Aluminum Electrolytic Capacitors Production Process Flow
https://www.youtube.com/watch?v=2EEAfQgbkc0

Aluminum Electrolytic Capacitors - Snap-in Type
Kingtronics P/N Load Life Temperatures Characteristic
GKT-SB 1000H 85°C Snap-in, High Ripple Current
GKT-SS 2000H 85°C Snap-in, High Ripple Current
GKT-ST 2000H 105°C Snap-in, High Ripple Current
GKT-SC 5000H 85°C Snap-in, High Ripple Current
GKT-SD 3000H 105°C Snap-in, High Ripple Current

Kingtronics A Better Solution for your sourcing of Snap-in type E-cap

For fixed capacitor for electromagnetic interference suppression and connection to the supply mains, do you want to get more FKT-MX X2 film capacitors details?

FKT-MX film capacitors have won the VDE and UL marks approval. 
DIN EN 60384-14 (VDE 0565-1-1):2014-04; EN 60384-14:2013-08
DIN EN 60384-14/A1 (VDE 0565-1-1/A1):2017-04; EN 60384-14:2013/A1:2016

The product also fulfills the requirements of
IEC 60384-14:2013
IEC 60384-14:2013/AMD1:2016

Rated capacitance: from 0, 0047 μF to 10, 0 μF
Rated voltage: AC 275/305/310 V
Capacitor class and subclass: X2
Climatic category: 40/110/56
Tolerance of rated capacitance: ±10 % (K); ±20 % (M)

In response to the needs of high-quality customers, Kingtronics launched new FKT-MX X2 Class box film capacitors to meet your needs.

FKT-MX series is fixed capacitor for electromagnetic interference, suppression and connection to the supply mains. Please feel free to contact us by info@kingtronics.com, thank you

Kingtronics FKT-MX X2 Class box film capacitors

Our FKT-MX X2 Metallized Polypropylene Film Capacitor is of high quality, short lead time, and competitive price! 

We can replace the below brands with much better offers and our parts are qualified with VDE, ENEC, and UL approvals. 
 
Welcome your inquiry. ^^ 
Kingtronics  Kemet (Arcotronics) Epcos Pilkor Evox Rifa
FKT-MX Class X2 R46 B81 130 PCX2 337 PHE 840M
(310VAC)  B32921~B32924 PCX2 339 PHE 840E
  Vishay Wima Iskra Panasonic
  MKP 3382 MP3 X2 KNB 153X ECQU
  MKP 3392 MKP X2 KNB 156X

Kingtronics new product line-- Film Capacitors-- FKT series
https://www.youtube.com/watch?v=cDcynh4c1o0

The PCB is prone to bending and warping when it passes through the reflow furnace, which makes people very distressed. So how to prevent PCB board from bending and warping through the reflow furnace? Let's explain it to you:

1.Reduce the influence of temperature on PCB stress
Since "temperature" is the main source of plate stress, as long as the temperature of the reflow furnace is reduced or the heating and cooling rate of the plate in the reflow furnace is slowed down, the occurrence of plate bending and plate warping can be greatly reduced. However, there may be other side effects, such as solder short circuit.

2.Use high Tg plate
Tg is the glass transition temperature, that is, the temperature at which the material changes from glass to rubber. The lower the Tg value of the material, the faster the plate begins to soften after entering the reflow furnace, and the longer the time to become soft rubber, the more serious the deformation of the plate. The use of plates with higher Tg can increase their ability to withstand stress and deformation, but the price of materials is relatively high.

3.Increase the thickness of the circuit board
In order to achieve the goal of thinner, many electronic products have left 1.0mm, 0.8mm and even 0.6mm thick plates. It is really a bit difficult to keep the plates from deforming after the reflow furnace. It is suggested that if there is no requirement of thinner, the plates can preferably use 1.6mm thick plates, which can greatly reduce the risk of bending and deformation.

4.Reduce the size of circuit board and the number of panels
Since most of the reflow furnaces use chains to drive the circuit board forward, the larger size of the circuit board will be dented and deformed in the reflow furnace because of its own weight, so try to put the long side of the circuit board on the chain of the reflow furnace as far as possible, which can reduce the dented deformation caused by the weight of the circuit board itself. This is also the reason for the reduction of the number of panels, Try to use the narrow edge perpendicular to the direction of furnace passage to achieve the minimum concave deformation.

5.Used reflow carrier
If the above methods are difficult to achieve, the last is to use the reflow carrier/template to reduce the deformation. The reason why the reflow carrier can reduce the bending and warping of the plate is that the template is expected to hold the circuit board until the temperature of the circuit board is lower than the Tg value and begins to harden again, and can maintain the original size..

If the single-layer template cannot reduce the deformation of the circuit board, it is necessary to add another layer of cover to clamp the circuit board with the upper and lower layers of templates, which can greatly reduce the deformation of the circuit board through the reflow furnace. However, the template is very expensive, and it has to be placed and recycled manually.

6.Use Router instead of V-Cut
Since V-Cut will destroy the structural strength of the panels between the circuit boards, try not to use the sub-panels of V-Cut or reduce the depth of V-Cut.

Kingtronics Components to use on your board:
GKT-Aluminum Electrolytic Capacitors, radial, axial, SMD, snap-in, Lug, screw types
Bridge Rectifiers: MB1S-MB10S, KBPC6005-KBPC610, KBP2005-KBP210
Diodes & Transistors: M7, 1N4007, LL4148, BZV55C, Fast Recovery Diodes
DKT-Super Capacitors: 2.7V, 3V Radial, Snap-in, Screw Type and 5.5V Coin Type
MLCC and Tancap: Multilayer Ceramic Capacitors and Tantalum Capacitors
KKT-Ceramic Capacitors: SMD 3mm Trimmer Capacitor 3pF, 6pF,10pF, 20pF, 30pF
RKT-Trimming Potentiometers: Rectangular, SMD, Square 3006, 3362, 3386, 3590
QKT-Crystals: Crystals and Oscillators size 1612 to 7050,Tuning Fork 32.768KHz
SKT-Surge Arresters: Axial and SMD Gas 2-Electrode and 3-Electrode Arresters
NKT-NTC Thermistors: NTC Negative Temperature Coefficient Thermistor
XKT-Varistors: Metal Oxide Varistor 05D, 07D, 10D, 14D, 20D
WKT-Switches: DIP and SMD Tact Switches
FKT-Film Capacitors: Metallized Polyester and Polypropylene Film Capacitor

 

Kingtronics team is committed to helping our customers to cost down.
We are delighted to inform that we have better support for some values of our super capacitors now.
Please don’t hesitate to contact us to enjoy our latest best prices !

Kingtronics (Kt) Super Capacitors Features
Standard coin-type, Radial type, Snap-in type, Screw Type terminals
Small-sized, large capacity
High energy and high power
Low ESR
Pb-free and RoHS compliant

Kingtronics (Kt) Super Capacitors Applications
RAM, Detonator, car recorder, smart meter
Vacuum switch, digital camera, motor drive, clock circuit
UPS, toy, program-controlled switch, etc.

Kingtronics standard series of super capacitors
DKT-DZ, super capacitor Radial Type, Snap-in Type, Screw Type, low ESR
DKT-DX, super capacitor, radial type
DKT-DA, super capacitor, Coin Type, small size, large capacity
DKT-DM, super capacitor, Combined Type (Double Layer Capacitors), Low internal resistance
DKT-DY, super capacitor, Combined Type (Double Layer Capacitors), Low leakage current 

Contact us

Tel: (86) 769 8118 8110
Tel: (852) 8106 7033
Fax: (852) 8106 7099
E-mail: info@kingtronics.com
Skype: kingtronics.sales
MSN: kingtronics-sales@hotmail.com
Web: www.Kingtronics.com
YouTube: www.youtube.com/c/Kingtronicskt

About

Kingtronics International Company was established in 1995 located in Dongguan City of China to handle all sales & marketing for factories located in Chengdu, Sichuan and Zhaoqing, Guangdong, China. In 1990, we established the first factory to produce trimming potentiometer and in 1999 we built up new factory in Zhao Qing, Guangdong. Now with around 850 workers, Kingtronics produce trimming potentiometers, dipped tantalum capacitors, multilayer ceramic capacitors, and diode & bridge rectifier. We sell good quality under our brand Kingtronics, and Kt, King, Kingtronics are our three trademarks. All our products are RoHS compliant, and our bridge rectifier have UL approval. Please visit our Products page, you could please download all our PDF datasheet and find cross reference for our Trimming Potentiometer and capacitors.

Tantalum and Ceramic Capacitors Cross Reference ↓ Download
Diodes & Rectifiers List(PDF: 97KB) ↓ Download
Trimming Potentiometer Cross Reference ↓Download

Archives

Calendar

<< 2024-4 >>

Sun

Mon

Tue

Wed

Thu

Fri

Sat

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30